10/100BASE-T SFPCisco XFP10GLR-192SR-L Compatible XFP XFP 10GBASE-LR/LW Transceiver Module
The XFP10GLR-192SR-L compatible module serves equipment requiring a XFP XFP interface with 1310nm optics and a 10km rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support high-density deployments balance optical performance, port access and thermal planning.
OEM Part Number: XFP10GLR-192SR-LHT Part Number: XFP-10GLR-31
Product Highlights
- Compatible alternative to Cisco XFP10GLR-192SR-L
- XFP connectivity at 11.3Gbps
- Optical wavelength: 1310nm
- Specified reach: 10km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | XFP-10GLR-31 |
|---|---|
| Manufacturer | HT |
| Form Factor | XFP |
| Max. Data Rate | 11.3Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 10km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | DFB |
| Receiver Type | PIN |
| TX Power | -6~0dBm |
| Receiver Sensitivity | <-12.6dBm |
| Power Budget | 6.6dB |
| Receiver Overload | 0dBm |
| Max. Power Consumption | ≤1.5W |
| Extinction Ratio | 3.5dB |
| DDM/DOM | Supported |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Core Size | 9/125 µm |
| Modulation | NRZ |
| Protocols | IEEE 802.3ae, XFP MSA |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The XFP interface configuration must match the remote equipment; sharing a XFP housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 10km. Inspect every Duplex LC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6~0dBm; receiver sensitivity is <-12.6dBm; the stated optical power budget is 6.6dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 11.3Gbps, wavelength 1310nm, rated reach 10km.
Ordering Information
Quote HT part number XFP-10GLR-31 together with OEM reference XFP10GLR-192SR-L and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Cisco Compatibility and Factory Testing
The module is checked for host recognition as XFP10GLR-192SR-L, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies XFP10GLR-192SR-L, not an original Cisco-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
