JD108AHPE H3C JD108A Compatible XFP XFP 10GBASE-LR Transceiver Module
Built for hosts recognizing JD108A, this HT-manufactured XFP module delivers XFP transmission at 1310nm. Its rated reach is 10km, with Duplex LC as the physical interface. The specifications and engineering guidance below support high-density deployments balance optical performance, port access and thermal planning, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: JD108AHT Part Number: XFP-10GLR-31
Product Highlights
- Compatible alternative to HPE H3C JD108A
- XFP connectivity at 11.3Gbps
- Optical wavelength: 1310nm
- Specified reach: 10km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | XFP-10GLR-31 |
|---|---|
| Manufacturer | HT |
| Form Factor | XFP |
| Max. Data Rate | 11.3Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 10km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | DFB |
| Receiver Type | PIN |
| TX Power | -6~0dBm |
| Receiver Sensitivity | <-12.6dBm |
| Power Budget | 6.6dB |
| Receiver Overload | 0dBm |
| Max. Power Consumption | ≤1.5W |
| Extinction Ratio | 3.5dB |
| DDM/DOM | Supported |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Core Size | 9/125 µm |
| Modulation | NRZ |
| Protocols | IEEE 802.3ae, XFP MSA |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The XFP interface configuration must match the remote equipment; sharing a XFP housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 10km route. Keep the Duplex LC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Quality Assurance and Packaging
Each JD108A compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6~0dBm; receiver sensitivity is <-12.6dBm; the stated optical power budget is 6.6dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 11.3Gbps, wavelength 1310nm, rated reach 10km.
Ordering Information
When ordering, specify JD108A, XFP-10GLR-31, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
HPE H3C Compatibility and Factory Testing
The module is checked for host recognition as JD108A, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original HPE H3C transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies JD108A, not an original HPE H3C-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
