OW-QSFP100G40-95Generic OW-QSFP100G40-95 Compatible 100G QSFP28 Transceiver Module
Built for hosts recognizing OW-QSFP100G40-95, this HT-manufactured QSFP28 module delivers 100G transmission at 1295.56nm. Its rated reach is 40km, with Duplex LC/UPC as the physical interface. The specifications and engineering guidance below support high-density deployments balance optical performance, port access and thermal planning, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: OW-QSFP100G40-95HT Part Number: OW-QSFP100G40-95
Product Highlights
- Compatible alternative to Generic OW-QSFP100G40-95
- 100G connectivity at 100Gbps
- Optical wavelength: 1295.56nm
- Specified reach: 40km
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C
Specifications
| HT Part Number | OW-QSFP100G40-95 |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max Data Rate | 100Gbps |
| Wavelength | 1295.56nm |
| Max Cable Distance | 40km |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | APD |
| TX Power | 1.7~7.1dBm |
| RX Power | -15.7~-3dBm |
| Power Consumption | 5.5W |
| Extinction Ratio | 5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C |
| Modulation Format | PAM4 |
| Damage Threshold | -2.4dBm |
| FEC Function | KP1 FEC |
| Protocols | QSFP28 MSA, SFF-8636, IEEE 802.3bs |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 40km. Inspect every Duplex LC/UPC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 1.7~7.1dBm. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 100Gbps, wavelength 1295.56nm, rated reach 40km.
Ordering Information
Use OW-QSFP100G40-95 as the compatibility cross-reference and OW-QSFP100G40-95 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Generic Compatibility and Factory Testing
Compatibility testing for OW-QSFP100G40-95 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 40km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
