QSFP-ER4L-100GMGeneric QSFP-ER4L-100GM Compatible 100G QSFP28 ER4L Transceiver Module
The QSFP-ER4L-100GM compatible module serves equipment requiring a 100G QSFP28 interface with 1310nm* optics and a 30km on SMF rating. Connection is through LC duplex. Product data, application guidance and factory verification are presented together to support high-density deployments balance optical performance, port access and thermal planning.
OEM Part Number: QSFP-ER4L-100GMHT Part Number: QSFP-ER4L-100GM
Product Highlights
- Compatible alternative to Generic QSFP-ER4L-100GM
- 100G connectivity at Dual Rate 103.1Gbps and 112Gbps
- Optical wavelength: 1310nm*
- Specified reach: 30km on SMF
- LC duplex / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Generic | QSFP-100G-ER4 |
|---|---|
| Manufacturer | HT |
| HT Part Number | QSFP-ER4L-100GM |
| Form Factor | QSFP28 |
| Data Rate | Dual Rate 103.1Gbps and 112Gbps |
| Wavelength | 1310nm* |
| Max Cable Distance | 30km@SMF |
| Connector | LC duplex |
| Media | SMF |
| Transmitter Type | 4 x LAN WDM DML TOSA |
| Receiver Type | 4 x PIN ROSA |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| TX Power(100G) | -2.5~4.5dBm |
| Receiver Sensitivity(100G) | <-15dBm |
| TX Power(112G) | -1.5~4.5dBm |
| Receiver Sensitivity(112G) | <-14.5dBm |
| Power Consumption | 4.5W |
| Extinction Ratio | 4dB |
| Modulation Format | NRZ |
| CDR | TX and RX |
| Transmit and Dispersion Penalty | 2.5dB |
| Power Budget | 14.4dB |
| Packaging Technology | BOX Packaging |
| FEC Function** | Supported |
| Protocols | 100G Ethernet, 100G Telecom Connections, Infiniband QDR and DDR Interconnects |
| Application | 100GBASE Ethernet, Telecom, 5G Network Mid/Backhaul |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 30km on SMF route. Keep the LC duplex interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Quality Assurance and Packaging
Each QSFP-ER4L-100GM compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the stated optical power budget is 14.4dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate Dual Rate 103.1Gbps and 112Gbps, wavelength 1310nm*, rated reach 30km on SMF.
Ordering Information
Use QSFP-ER4L-100GM as the compatibility cross-reference and QSFP-ER4L-100GM as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Generic Compatibility and Factory Testing
Compatibility testing for QSFP-ER4L-100GM combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use LC duplex with SMF. The specified maximum reach is 30km on SMF, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
