TN-X2-10GB-ERTransition Networks TN-X2-10GB-ER Compatible XFP X2 10GBASE-ER Transceiver Module
The TN-X2-10GB-ER compatible module serves equipment requiring a XFP X2 interface with 1550nm optics and a 40km rating. Connection is through SC duplex. Product data, application guidance and factory verification are presented together to support high-density deployments balance optical performance, port access and thermal planning.
OEM Part Number: TN-X2-10GB-ERHT Part Number: TN-X2-10GB-ER
Product Highlights
- Compatible alternative to Transition Networks TN-X2-10GB-ER
- XFP connectivity at 10Gbps
- Optical wavelength: 1550nm
- Specified reach: 40km
- SC duplex / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Transition Networks Compatible | TN-X2-10GB-ER |
|---|---|
| Manufacturer | HT |
| HT Part Number | TN-X2-10GB-ER |
| Form Factor | X2 |
| Max. Data Rate | 10Gbps |
| Wavelength | 1550nm |
| Max. Transmission Distance | 40km |
| Connector | SC duplex |
| Transmitter Type | EML 1550nm |
| Media | SMF |
| DOM Support | Yes |
| TX Power | -4.7~4dBm |
| Receiver Sensitivity | < -15.8dBm |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The XFP interface configuration must match the remote equipment; sharing a X2 housing alone does not make two transceiver types interoperable.
For this 1550nm interface, verify channel spacing and filter compatibility. Passive filters add loss even without active equipment, so assess 40km using the complete channel rather than fiber distance alone.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4.7~4dBm; receiver sensitivity is < -15.8dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 10Gbps, wavelength 1550nm, rated reach 40km.
Ordering Information
Use TN-X2-10GB-ER as the compatibility cross-reference and TN-X2-10GB-ER as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Transition Networks Compatibility and Factory Testing
Factory verification starts with the expected TN-X2-10GB-ER identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Transition Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies TN-X2-10GB-ER, not an original Transition Networks-branded module.
Which fiber and connector are required?
Use SC duplex with SMF. The specified maximum reach is 40km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
