10/100BASE-T SFPIntel SFP-10GM-T-30 Compatible 10G SFP+ Transceiver Module
The SFP-10GM-T-30 compatible module serves equipment requiring a 10G SFP+ interface with the listed wavelength plan optics and a 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable rating. Connection is through RJ-45. Product data, application guidance and factory verification are presented together to support high-density deployments balance optical performance, port access and thermal planning.
OEM Part Number: SFP-10GM-T-30HT Part Number: SFP-10GM-T-30
Product Highlights
- Compatible alternative to Intel SFP-10GM-T-30
- 10G connectivity at 10.3125Gbps
- Specified reach: 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable
- RJ-45 / Copper interface
- Digital diagnostic monitoring: Not Implemented
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and electrical performance testing before shipment
Specifications
| HT Part Number | SFP-10GM-T-30 |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ |
| Max. Data Rate | 10.3125Gbps |
| Max. Power Consumption | ≤2.5W |
| Max. Transmission Distance | 10/100/1000M-100m@Cat 5 Cable or better10G-30m@Cat 6a/7 Cable |
| Connector | RJ-45 |
| Cable Type | Copper |
| Special Features | RX_LOS |
| DDM/DOM | Not Implemented |
| Multi-rate Application | Supported (Auto-negotiation) |
| MTBF | 6430000 Hours |
| EMC (Electro Magnetic Compatibility) | Supported |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE 802.3az SFP+ MSA |
Applications and Optical Link Design
This copper transceiver is intended for short equipment links over the twisted-pair cabling category stated in the specifications. Typical uses include switch-to-server, switch-to-switch and rack-level connections where an RJ-45 interface is preferred over fiber. Use the required cable category, observe the rated distance and confirm that the host supports the module’s speed, power consumption and electrical operating modes.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
The rated 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable copper channel should be assessed as a complete cabling link. Confirm cable category, shielding practice and supported host mode before installation. A link indicator alone does not prove that the expected electrical rate has been established.
Quality Assurance and Packaging
Each SFP-10GM-T-30 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Not Implemented. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 10.3125Gbps, rated reach 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable.
Ordering Information
Quote HT part number SFP-10GM-T-30 together with OEM reference SFP-10GM-T-30 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Intel Compatibility and Factory Testing
Factory verification starts with the expected SFP-10GM-T-30 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Intel transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-10GM-T-30, not an original Intel-branded module.
Which copper cable and connector are required?
Use RJ-45 with the specified category of Copper. The rated reach is 10 / 100 / 1000M-100m on Cat 5 Cable or better10G-30m on Cat 6a / 7 Cable, subject to cable category, installation quality and host support.
Can it be used at a different speed or over another cable category?
Only within the multi-rate and cabling capabilities stated in the specifications and supported by the host. Confirm the required cable category, distance and auto-negotiation behavior before installation.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
