10/100BASE-T SFPIBM SFP-10GLRM-31 Compatible 10G SFP+ LRM Transceiver Module
Built for hosts recognizing SFP-10GLRM-31, this HT-manufactured SFP+ module delivers 10G transmission at 1310nm. Its rated reach is 220m on OM3 / 300m on SMF, with Duplex LC as the physical interface. The specifications and engineering guidance below support high-density deployments balance optical performance, port access and thermal planning, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SFP-10GLRM-31HT Part Number: SFP-10GLRM-31
Product Highlights
- Compatible alternative to IBM SFP-10GLRM-31
- 10G connectivity at 10.3125Gbps
- Optical wavelength: 1310nm
- Specified reach: 220m on OM3 / 300m on SMF
- Duplex LC / MMF/SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | SFP-10GLRM-31 |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ |
| Max. Data Rate | 10.3125Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 220m@OM3/300m@SMF |
| Connector | Duplex LC |
| Transmitter Type | FP 1310nm |
| Media | MMF/SMF |
| DOM Support | Yes |
| TX Power | -6.5~-0.5dBm |
| Receiver Sensitivity | < -8.4dBm |
| Max. Power Consumption | ≤1W |
| Receiver Overload | +1.5dBm |
| Core Size | 50/125µm@OM3 MMF, 9/125μm@SMF |
| Modulation | NRZ |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Bit Error Ratio (BER) | 1E-12 |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 220m on OM3 / 300m on SMF figure applies only under suitable cabling conditions. Inspect every Duplex LC mating point and match the remote optical standard.
Quality Assurance and Packaging
Each SFP-10GLRM-31 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6.5~-0.5dBm; receiver sensitivity is < -8.4dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 10.3125Gbps, wavelength 1310nm, rated reach 220m on OM3 / 300m on SMF.
Ordering Information
Use SFP-10GLRM-31 as the compatibility cross-reference and SFP-10GLRM-31 as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
IBM Compatibility and Factory Testing
Factory verification starts with the expected SFP-10GLRM-31 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original IBM transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-10GLRM-31, not an original IBM-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF/SMF. The specified maximum reach is 220m on OM3 / 300m on SMF, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
