QSFP56 to SFP56-200G-AOC-7M23FTQSFP56 to SFP56-200G-AOC-7M23FT 200G QSFP56 4 x 50G PAM4 to 4 x 50G SFP56 50G PAM4 Active Optical Breakout Cable, 7m (23ft)
For densely populated equipment, the fixed 7m (23ft) version of Generic QSFP56 to SFP56-200G-AOC-7M23FT offers a clearly defined 200G link without separate optical modules or patch cords. The AOC assembly uses QSFP56 to SFP56; its power, mechanical and diagnostic details are listed where supplied so port density and cable management can be assessed together.
OEM Part Number: QSFP56 to SFP56-200G-AOC-7M23FTHT Part Number: QSFP56 to SFP56-200G-AOC-7M23FT
Product Highlights
- HT-manufactured AOC assembly in 7m (23ft)
- 200G connectivity at 200G
- Interface configuration: QSFP56 to SFP56
- Fixed length and part number: 7m (23ft), QSFP56 to SFP56-200G-AOC-7M23FT
- Minimum bend radius: 30mm
Specifications
| HT Part Number | QSFP56 to SFP56-200G-AOC-7M23FT |
|---|---|
| Manufacturer | HT |
| Connector Type | QSFP56 to SFP56 |
| Max Data Rate | 200G |
| Minimum Bend Radius | 30mm |
| Cable Length | 7m (23ft) |
| Receiver Type | PIN |
| Transmitter Type | VSCEL |
| Temperature | 0 to 70°C (32 to 158°F) |
| Jacket Material | OFNP |
| Typical Power Consumption | 5.5W (QSFP56), 3W (SFP56) |
| Power Supply | 3.3V |
| Wavelength | 850nm |
| Fiber Type | OM3 Multimode Fiber (MMF) |
Cable Construction and Routing
This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
A 7m (23ft) run can remain tidy when its pathway and service allowance are planned together. Keep the integrated optical cable and both optical engines away from tight cable-tie pressure, verify bend control at changes of direction and ensure that neither port supports the assembly’s weight. Record the exact order code after acceptance. Within this family, QSFP56 to SFP56-200G-AOC-5M16FT is shorter at 5m (16ft), while QSFP56 to SFP56-200G-AOC-10M33FT is the next longer choice at 10m (33ft); comparing those two boundaries helps avoid both tension and unnecessary slack.
Position Within the Length Range
QSFP56 to SFP56-200G-AOC-7M23FT occupies the middle of this family between QSFP56 to SFP56-200G-AOC-5M16FT at 5m (16ft) and QSFP56 to SFP56-200G-AOC-10M33FT at 10m (33ft). It adds 2m over the shorter option for extra routing clearance, while the next longer version adds another 3m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
High-Density Rack Integration
In a densely populated rack, connector access and airflow are part of the link design. Choose the shortest length that follows the managed path comfortably, avoid tight bundles around the connector housings and preserve room for latch operation. Where power consumption is listed, include every populated interface in the host thermal budget rather than assessing a single cable in isolation. For this assembly, the minimum bend radius is 30mm; the jacket material is OFNP.
Breakout Port Mapping
The QSFP56 to SFP56 configuration divides the high-speed interface into multiple lower-speed connections. Verify the upstream lane assignment, downstream port speeds and breakout setting on the host before connecting the assembly. Each branch must attach to the correct remote interface.
Quality Assurance and Packaging
Each assembly receives a visual connector inspection and functional link check before it is coiled and protected. Packaging is selected to avoid compressing the cable into a tight bundle, and optional rack-based labels help maintain an orderly installation when many identical interfaces are populated together. Volume orders can include customer references on the labels and carton list.
Ordering Information
Provide the exact part number, length, quantity and target interface density. For multi-rack projects, list each length separately and identify any preferred carton grouping. Host model and software information can be included for a compatibility review before production or dispatch. Keep QSFP56 to SFP56-200G-AOC-7M23FT associated with 7m (23ft) throughout the order and receiving record.
Generic Compatibility and Factory Testing
The assembly is evaluated for host recognition and stable link operation, with diagnostics checked where the interface provides them. This approach verifies more than electrical or optical continuity. Exact platform and firmware information remains valuable in high-density deployments because port mode and qualification policy can differ within the same connector family. Both connectors are examined before the operating test, which includes receive activity and diagnostic indications.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
Does this order code cover multiple lengths?
No. QSFP56 to SFP56-200G-AOC-7M23FT refers here to 7m (23ft). Every other verified length has a separate part number and page in the length list.
Are separate transceivers or patch leads required?
No. This is one complete direct-attach assembly. The ends are not detachable modules and should not be separated from the cable.
Can excess cable be folded into a compact bundle?
No. Use a supported, bend-safe service loop and observe the listed minimum bend radius. Do not crease the cable or tighten ties around the connector boots.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production quantities confirmed at order stage. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.
