QSFP-ZR4-100G-ICisco QSFP-ZR4-100G-I Compatible 100G QSFP28 ZR4 Transceiver Module
The QSFP-ZR4-100G-I compatible module serves equipment requiring a 100G QSFP28 interface with 1310nm optics and a 80km rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support high-density deployments balance optical performance, port access and thermal planning.
OEM Part Number: QSFP-ZR4-100G-IHT Part Number: QSFP-ZR4-100G-I
Product Highlights
- Compatible alternative to Cisco QSFP-ZR4-100G-I
- 100G connectivity at 103.125Gbps (4x 25.78Gbps)
- Optical wavelength: 1310nm
- Specified reach: 80km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -40 to 85°C (-40 to 185°F)
Specifications
| HT Part Number | QSFP-ZR4-100G-I |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max Data Rate | 103.125Gbps (4x 25.78Gbps) |
| Wavelength | 1310nm |
| Max Cable Distance | 80km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | LAN WDM EML |
| Receiver Type | SOA+PIN |
| TX Power | 2.0~6.5dBm |
| RX Power | -28.0~-5dBm |
| Power Consumption | ≤7W |
| Extinction Ratio | >6dB |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | Yes |
| DDM/DOM | Supported |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| Core Size | 9um/125um |
| Packaging Technology | BOX Packaging |
| Protocols | IEEE 802.3ba, QSFP28 MSA |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
Before commissioning, measure the complete single-mode channel against the stated budget for 80km. Inspect every Duplex LC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 2.0~6.5dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 103.125Gbps (4x 25.78Gbps), wavelength 1310nm, rated reach 80km.
Ordering Information
Quote HT part number QSFP-ZR4-100G-I together with OEM reference QSFP-ZR4-100G-I and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Cisco Compatibility and Factory Testing
Compatibility testing for QSFP-ZR4-100G-I combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-ZR4-100G-I, not an original Cisco-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 80km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
