10/100BASE-T SFPNetgear QSFP-SR1.2-100G Compatible 100G QSFP28 SR1.2 Transceiver Module
Built for hosts recognizing QSFP-SR1.2-100G, this HT-manufactured QSFP28 module delivers 100G transmission at 850/910nm. Its rated reach is 70m on OM3 / 100m on OM4 / 150m on OM5, with Duplex LC as the physical interface. The specifications and engineering guidance below support high-density deployments balance optical performance, port access and thermal planning, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-SR1.2-100GHT Part Number: QSFP-SR1.2-100G
Product Highlights
- Compatible alternative to Netgear QSFP-SR1.2-100G
- 100G connectivity at 106.25 Gbps
- Optical wavelength: 850/910nm
- Specified reach: 70m on OM3 / 100m on OM4 / 150m on OM5
- Duplex LC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -10 to 60 ℃ (14 to 140°F)
Specifications
| HT Part Number | QSFP-SR1.2-100G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max. Data Rate | 106.25 Gbps |
| Wavelength | 850/910nm |
| Max. Cable Distance | 70m@OM3/100m@OM4/150m@OM5 |
| Connector | Duplex LC |
| Media | MMF |
| Transmitter Type | Broadcom/AFCD-V7 |
| Receiver Type | PIN |
| TX Power | -6.2dBm~4dBm |
| Minimum Receiver Power | -8.2dBm |
| Power Budget | 2dB |
| Receiver Overload | 4dBm |
| Power Consumption | ≤4W |
| Extinction Ratio | >3dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | -10 to 60 ℃ (14 to 140°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 2x 50G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | KP4 FEC |
| Packaging Technology | COB Packaging |
| Core Size | 50um/125um |
| Protocols | QSFP28 MSA and IEEE 802.3bm CAUI-4 |
Applications and Optical Link Design
This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
For this coherent interface, document the wavelength plan and modulation or FEC settings before commissioning. Measure span loss and verify adequate OSNR. Interoperability depends on compatible coherent modes as well as form factor, so another coherent part number must not be substituted without engineering review.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6.2dBm~4dBm; the stated optical power budget is 2dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 106.25 Gbps, wavelength 850/910nm, rated reach 70m on OM3 / 100m on OM4 / 150m on OM5.
Ordering Information
When ordering, specify QSFP-SR1.2-100G, QSFP-SR1.2-100G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Netgear Compatibility and Factory Testing
The module is checked for host recognition as QSFP-SR1.2-100G, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Netgear transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-SR1.2-100G, not an original Netgear-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF. The specified maximum reach is 70m on OM3 / 100m on OM4 / 150m on OM5, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
