10/100BASE-T SFPH3C QSFP-SL4-200G Compatible 200G QSFP56 SL4 Transceiver Module
Built for hosts recognizing QSFP-SL4-200G, this HT-manufactured QSFP56 module delivers 200G transmission at 850nm. Its rated reach is 30m, with MPO-12/UPC as the physical interface. The specifications and engineering guidance below support high-density deployments balance optical performance, port access and thermal planning, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-SL4-200GHT Part Number: QSFP-SL4-200G
Product Highlights
- Compatible alternative to H3C QSFP-SL4-200G
- 200G connectivity at 200Gbps
- Optical wavelength: 850nm
- Specified reach: 30m
- MPO-12/UPC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-SL4-200G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP56 |
| Max. Data Rate | 200Gbps |
| Wavelength | 850nm |
| Max. Cable Distance | 30m |
| Connector | MPO-12/UPC |
| Media | MMF |
| Transmitter Type | VCSEL 850nm |
| Receiver Type | PIN |
| TX Power | -3~3dBm |
| Minimum Receiver Power | -6.5dBm |
| Power Budget | 3.5dBm |
| Receiver Overload | 5dBm |
| Max. Power Consumption | 4.35W |
| Extinction Ratio | 3dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x50G-PAM4 |
| Modulation (Optical) | 4x50G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | Support RS-FEC |
| Protocols | IEEE 802.3bs, QSFP56 MSA, SFF-8665, SFF-8636 |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MPO-12/UPC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 200G interface configuration must match the remote equipment; sharing a QSFP56 housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 30m reach. Keep the MPO-12/UPC end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3~3dBm; the stated optical power budget is 3.5dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 200Gbps, wavelength 850nm, rated reach 30m.
Ordering Information
Quote HT part number QSFP-SL4-200G together with OEM reference QSFP-SL4-200G and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
H3C Compatibility and Factory Testing
Compatibility testing for QSFP-SL4-200G combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original H3C transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-SL4-200G, not an original H3C-branded module.
Which fiber and connector are required?
Use MPO-12/UPC with MMF. The specified maximum reach is 30m, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
