QSFP-LX4-100GArista QSFP-LX4-100G Compatible 100G QSFP28 LX4 Transceiver Module
Built for hosts recognizing QSFP-LX4-100G, this HT-manufactured QSFP28 module delivers 100G transmission at 1271nm,1291nm,1311nm,1331nm. Its rated reach is 2km on SMF / 100m on OM3 MMF, with Duplex LC as the physical interface. The specifications and engineering guidance below support high-density deployments balance optical performance, port access and thermal planning, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-LX4-100GHT Part Number: QSFP-LX4-100G
Product Highlights
- Compatible alternative to Arista QSFP-LX4-100G
- 100G connectivity at 103.12Gbps (4x 25.78GGbps)
- Optical wavelength: 1271nm,1291nm,1311nm,1331nm
- Specified reach: 2km on SMF / 100m on OM3 MMF
- Duplex LC / SMF/MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-LX4-100G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max. Data Rate | 103.12Gbps (4x 25.78GGbps) |
| Wavelength | 1271nm,1291nm,1311nm,1331nm |
| Max. Cable Distance | 2km@SMF/100m@OM3 MMF |
| Connector | Duplex LC |
| Media | SMF/MMF |
| Transmitter Type | CWDM4 DFB |
| Receiver Type | PIN |
| TX Power | -3~4.5dBm |
| Minimum Receiver Power | -7.3dBm |
| Power Budget | 4.3dB |
| Receiver Overload | 4.5dBm |
| Power Consumption | ≤4.5W |
| Extinction Ratio | >3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| Inbuilt FEC | Yes |
| Packaging Technology | COB (Chip on Board) Packaging |
| Protocols | IEEE Std 802.3bm-2015, SFF-8665 Rev 1.9, SFF-8636 Rev 2.10a, SFF-8679 Rev 1.8 |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 2km on SMF / 100m on OM3 MMF reach. Keep the Duplex LC end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3~4.5dBm; the stated optical power budget is 4.3dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 103.12Gbps (4x 25.78GGbps), wavelength 1271nm,1291nm,1311nm,1331nm, rated reach 2km on SMF / 100m on OM3 MMF.
Ordering Information
When ordering, specify QSFP-LX4-100G, QSFP-LX4-100G, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Arista Compatibility and Factory Testing
The module is checked for host recognition as QSFP-LX4-100G, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Arista transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-LX4-100G, not an original Arista-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF/MMF. The specified maximum reach is 2km on SMF / 100m on OM3 MMF, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
