10/100BASE-T SFPDell QDD-PLR4-400G Compatible 400G QSFP-DD PLR4 Transceiver Module
This Dell QDD-PLR4-400G compatible transceiver provides 400G connectivity in a hot-swappable QSFP-DD package. Its optical design operates at 1310nm for up to 10km, using MPO-12/APC. Complete parameters and related OEM references help high-density deployments balance optical performance, port access and thermal planning.
OEM Part Number: QDD-PLR4-400GHT Part Number: QDD-PLR4-400G
Product Highlights
- Compatible alternative to Dell QDD-PLR4-400G
- 400G connectivity at 425Gbps (4x 106.25Gbps)
- Optical wavelength: 1310nm
- Specified reach: 10km
- MPO-12/APC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QDD-PLR4-400G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP-DD |
| Max. Data Rate | 425Gbps (4x 106.25Gbps) |
| Wavelength | 1310nm |
| Max. Cable Distance | 10km |
| Connector | MPO-12/APC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | PIN |
| TX Power | -1.9~4.8dBm |
| Minimum Receiver Power | -8.2dBm |
| Power Budget | 6.3dB |
| Receiver Overload | 4.8dBm |
| Max. Power Consumption | 9W |
| Extinction Ratio | 3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x50G-PAM4 |
| Modulation (Optical) | 4x100G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in DSP |
| Host FEC | Supported |
| Protocols | QSFP-DD MSA HW Rev 5.1, QSFP-DD, CMIS Rev 5.0, IEEE 802.3cu, IEEE 802.3bs |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a QSFP-DD housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 10km route. Keep the MPO-12/APC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -1.9~4.8dBm; the stated optical power budget is 6.3dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 425Gbps (4x 106.25Gbps), wavelength 1310nm, rated reach 10km.
Ordering Information
Use QDD-PLR4-400G as the compatibility cross-reference and QDD-PLR4-400G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Dell Compatibility and Factory Testing
Compatibility testing for QDD-PLR4-400G combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Dell transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QDD-PLR4-400G, not an original Dell-branded module.
Which fiber and connector are required?
Use MPO-12/APC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
