10/100BASE-T SFPGeneric OSFP800-XDR8-B2 Compatible 800G Twin-port OSFP IHS/Closed Finned Top Transceiver Module
This Generic OSFP800-XDR8-B2 compatible transceiver provides 800G connectivity in a hot-swappable Twin-port OSFP IHS/Closed Finned Top package. Its optical design operates at 1310nm for up to 2km, using Dual MPO-12/APC. Complete parameters and related OEM references help high-density deployments balance optical performance, port access and thermal planning.
OEM Part Number: OSFP800-XDR8-B2HT Part Number: OSFP800-XDR8-B2
Product Highlights
- Compatible alternative to Generic OSFP800-XDR8-B2
- 800G connectivity at 850Gbps (8x 106.25Gbps)
- Optical wavelength: 1310nm
- Specified reach: 2km
- Dual MPO-12/APC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | OSFP800-XDR8-B2 |
|---|---|
| Manufacturer | HT |
| Form Factor | Twin-port OSFP IHS/Closed Finned Top |
| Max Data Rate | 850Gbps (8x 106.25Gbps) |
| Wavelength | 1310nm |
| Max Cable Distance | 2km |
| Connector | Dual MPO-12/APC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | Siphotonics PIN |
| TX Power | -3.1~4dBm |
| Minimum Receiver Power | -7.1dBm |
| Power Budget | 4dB |
| Receiver Overload | 4dBm |
| Max Power Consumption | 16.5W |
| Extinction Ratio | >3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x100G-PAM4 |
| Modulation (Optical) | Dual 4x100G-PAM4 |
| CDR (Clock and Data Recovery) | TX and RX Built-in DSP |
| Packaging Technology | COB (Chip on Board) Packaging |
| Bit Error Ratio (BER) | 2.4E-4 |
| MTBF | 3,222,983 Hours (@40°C, 60% CL)1,632,641 Hours (@40°C, 90% CL) |
| Protocols | IEEE 802.3ck, IEEE 802.3cu-2021, OSFP MSA, CMIS Rev 5.0 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 800G interface configuration must match the remote equipment; sharing a Twin-port OSFP IHS/Closed Finned Top housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 2km route. Keep the Dual MPO-12/APC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3.1~4dBm; the stated optical power budget is 4dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 850Gbps (8x 106.25Gbps), wavelength 1310nm, rated reach 2km.
Ordering Information
When ordering, specify OSFP800-XDR8-B2, OSFP800-XDR8-B2, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Generic Compatibility and Factory Testing
Factory verification starts with the expected OSFP800-XDR8-B2 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Dual MPO-12/APC with SMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
