Generic 400G AOCOSFP (IHS/Finned Top) to 2x QSFP56-400G-AOC-5M16FT 400G OSFP 8 x 50G PAM4 IHS/Finned Top to 2 x 200G QSFP56 4 x 50G PAM4 Active Optical Breakout Cable, 5m (16ft)
For densely populated equipment, the fixed 5m (16ft) version of Generic OSFP (IHS/Finned Top) to 2x QSFP56-400G-AOC-5M16FT offers a clearly defined 400G link without separate optical modules or patch cords. The AOC assembly uses OSFP (IHS/Finned Top) to 2x QSFP56; its power, mechanical and diagnostic details are listed where supplied so port density and cable management can be assessed together.
OEM Part Number: OSFP (IHS/Finned Top) to 2x QSFP56-400G-AOC-5M16FTHT Part Number: OSFP (IHS/Finned Top) to 2x QSFP56-400G-AOC-5M16FT
Product Highlights
- HT-manufactured AOC assembly in 5m (16ft)
- 400G connectivity at 400Gbps
- Interface configuration: OSFP (IHS/Finned Top) to 2x QSFP56
- Fixed length and part number: 5m (16ft), OSFP (IHS/Finned Top) to 2x QSFP56-400G-AOC-5M16FT
- Cable construction: Breakout AOC
- Maximum power consumption: 10W (OSFP End) 5.5W (QSFP56 Per End)
- Minimum bend radius: 30mm
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | OSFP (IHS/Finned Top) to 2x QSFP56-400G-AOC-5M16FT |
|---|---|
| Manufacturer | HT |
| Form Factor | OSFP (IHS/Finned Top) to 2x QSFP56 |
| Max. Data Rate | 400Gbps |
| Cable Length | 5m (16ft) |
| Cable Type | Breakout AOC |
| Wavelength | 850nm |
| Minimum Bend Radius | 30mm |
| Transmitter Type | VSCEL |
| Receiver Type | PIN |
| Max. Power Consumption | 10W (OSFP End) 5.5W (QSFP56 Per End) |
| Jacket Material | OFNP |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation Format | OSFP-8x 50G-PAM4QSFP56-4x 50G-PAM4 |
| Host FEC | Pre-FEC BER 2.4E-4, Post-FEC BER 1E-12 |
| Application | 400G/200G Ethernet |
| Protocols | IEEE 802.3cd, CMIS Rev. 4.0, SFF-8679, SFF-8661, SFF-8636 |
Signal and Lane Configuration
The listed modulation format is OSFP-8x 50G-PAM4QSFP56-4x 50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Breakout Port Mapping
The OSFP (IHS/Finned Top) to 2x QSFP56 configuration divides the high-speed interface into multiple lower-speed connections. Verify the upstream lane assignment, downstream port speeds and breakout setting on the host before connecting the assembly. Each branch must attach to the correct remote interface.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
The 5m (16ft) length gives OSFP (IHS/Finned Top) to 2x QSFP56-400G-AOC-5M16FT more freedom for adjacent-rack and row-end deployments. The integrated optical assembly should be supported along its route without tight bends or connector pull loads; the AOC specification and host support must still match the intended link.
Position Within the Length Range
OSFP (IHS/Finned Top) to 2x QSFP56-400G-AOC-5M16FT occupies the middle of this family between OSFP (IHS/Finned Top) to 2x QSFP56-400G-AOC-3M10FT at 3m (10ft) and OSFP (IHS/Finned Top) to 2x QSFP56-400G-AOC-10M33FT at 10m (33ft). It adds 2m over the shorter option for extra routing clearance, while the next longer version adds another 5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
High-Density Rack Integration
In a densely populated rack, connector access and airflow are part of the link design. Choose the shortest length that follows the managed path comfortably, avoid tight bundles around the connector housings and preserve room for latch operation. Where power consumption is listed, include every populated interface in the host thermal budget rather than assessing a single cable in isolation. For this assembly, the minimum bend radius is 30mm; the stated power consumption is 10W (OSFP End) 5.5W (QSFP56 Per End); the jacket material is OFNP.
Power and Thermal Planning
The rated power consumption is 10W (OSFP End) 5.5W (QSFP56 Per End). Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Cable Construction and Routing
This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Network and Protocol Considerations
The intended application is 400G/200G Ethernet. Listed interface and protocol references include IEEE 802.3cd, CMIS Rev. 4.0, SFF-8679, SFF-8661, SFF-8636. Confirm that the host firmware and port configuration support the same operating mode.
Quality Assurance and Packaging
Each assembly receives a visual connector inspection and functional link check before it is coiled and protected. Packaging is selected to avoid compressing the cable into a tight bundle, and optional rack-based labels help maintain an orderly installation when many identical interfaces are populated together. Standard protective packing is used by default, with project documentation arranged when requested.
Ordering Information
Provide the exact part number, length, quantity and target interface density. For multi-rack projects, list each length separately and identify any preferred carton grouping. Host model and software information can be included for a compatibility review before production or dispatch. Quantity and any labeling instructions should be attached specifically to OSFP (IHS/Finned Top) to 2x QSFP56-400G-AOC-5M16FT.
Generic Compatibility and Factory Testing
The assembly is evaluated for host recognition and stable link operation, with diagnostics checked where the interface provides them. This approach verifies more than electrical or optical continuity. Exact platform and firmware information remains valuable in high-density deployments because port mode and qualification policy can differ within the same connector family. Where supported by the host, receive activity and diagnostic indications are reviewed together with the established link.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
How should an unused assembly be stored?
Protect both connector ends, keep the cable in a loose bend-safe coil and retain its part-number label so the length and compatibility identity remain traceable.
Can different brands be connected with the same assembly?
Only where both hosts explicitly support the complete interface and compatibility arrangement. Document each end and select the appropriate brand-specific product when required.
Does this order code cover multiple lengths?
No. OSFP (IHS/Finned Top) to 2x QSFP56-400G-AOC-5M16FT refers here to 5m (16ft). Every other verified length has a separate part number and page in the length list.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production quantities confirmed at order stage. International express, air cargo and sea freight can be selected according to destination and carton volume; customer courier accounts and nominated forwarders are also accepted.
