MMS1V90-WRNVIDIA/Mellanox MMS1V90-WR Compatible 400G QSFP-DD LR4 Transceiver Module
The MMS1V90-WR compatible module serves equipment requiring a 400G QSFP-DD interface with 1271nm, 1291nm, 1311nm, and 1331nm optics and a 10km rating. Connection is through Duplex LC/UPC. Product data, application guidance and factory verification are presented together to support high-density deployments balance optical performance, port access and thermal planning.
OEM Part Number: MMS1V90-WRHT Part Number: QDD-LR4-400G
Product Highlights
- Compatible alternative to NVIDIA/Mellanox MMS1V90-WR
- 400G connectivity at 425Gbps (4x 106.25Gbps)
- Optical wavelength: 1271nm, 1291nm, 1311nm, and 1331nm
- Specified reach: 10km
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| NVIDIA/Mellanox Ethernet Compatible | MMS1V90-WR |
|---|---|
| Manufacturer | HT |
| HT Part Number | QDD-LR4-400G |
| Form Factor | QSFP-DD |
| Max. Data Rate | 425Gbps (4x 106.25Gbps) |
| Wavelength | 1271nm, 1291nm, 1311nm, and 1331nm |
| Max. Cable Distance | 10km |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | CWDM EML |
| Receiver Type | PIN |
| TX Power | -2.7~5.1dBm |
| Minimum Receiver Power | -9.0dBm |
| Power Budget | 6.3dB |
| Receiver Overload | 5.1dBm |
| Max. Power Consumption | 9W |
| Extinction Ratio | 3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x50G-PAM4 |
| Modulation (Optical) | 4x100G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in DSP |
| Inbuilt FEC | No |
| Core Size | G.652/9um |
| Packaging Technology | COB (Chip on Board) Packaging |
| Protocols | QSFP-DD MSA HW Rev 5.1, QSFP-DD, CMIS Rev 5.0, IEEE 802.3cu, 100G Lambda MSA |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a QSFP-DD housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 10km. Inspect every Duplex LC/UPC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -2.7~5.1dBm; the stated optical power budget is 6.3dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 425Gbps (4x 106.25Gbps), wavelength 1271nm, 1291nm, 1311nm, and 1331nm, rated reach 10km.
Ordering Information
Use MMS1V90-WR as the compatibility cross-reference and QDD-LR4-400G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
NVIDIA/Mellanox Compatibility and Factory Testing
The module is checked for host recognition as MMS1V90-WR, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original NVIDIA/Mellanox transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies MMS1V90-WR, not an original NVIDIA/Mellanox-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
