MFS1S00-H001VNVIDIA/Mellanox MFS1S00-H001V Compatible 200G QSFP56 4 x 50G PAM4 InfiniBand HDR Active Optical Cable, 1m (3ft)
The MFS1S00-H001V cable on this page is the 1m (3ft) version for NVIDIA/Mellanox hosts requiring 200G operation. Its QSFP56 to QSFP56 AOC construction reduces the connection to one factory-terminated assembly. Related lengths, brand cross-references and rack-integration notes support a precise high-density deployment.
OEM Part Number: MFS1S00-H001VHT Part Number: MFS1S00-H001V
Product Highlights
- Compatible alternative to NVIDIA/Mellanox MFS1S00-H001V
- 200G connectivity at 200Gbps
- Interface configuration: QSFP56 to QSFP56
- Fixed length and part number: 1m (3ft), MFS1S00-H001V
- Cable construction: OM3
- Maximum power consumption: 4.35W Per End
- Minimum bend radius: 30mm
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | MFS1S00-H001V |
|---|---|
| NVIDIA/Mellanox InfiniBand Compatible | MFS1S00-H001V |
| Manufacturer | HT |
| Connector Type | QSFP56 to QSFP56 |
| Max. Data Rate | 200Gbps |
| Minimum Bend Radius | 30mm |
| Cable Length | 1m (3ft) |
| Jacket Material | LSZH |
| Cable Type | OM3 |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| Wavelength | 850nm |
| Max. Power Consumption | 4.35W Per End |
| Power Supply | 3.3V |
| Modulation Format | PAM4 |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| DDM/DOM | Supported |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Protocols | IEEE 802.3, QSFP56 MSA, SFF-8665, SFF-8636, InfiniBand HDR |
| MTBF | ≈3.2 Million Hours |
Signal and Lane Configuration
The listed modulation format is PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Network and Protocol Considerations
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include IEEE 802.3, QSFP56 MSA, SFF-8665, SFF-8636, InfiniBand HDR. Confirm that the host firmware and port configuration support the same operating mode.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
At 1m (3ft), MFS1S00-H001V is a practical choice for direct connections within one rack. Route the cable along the intended management path rather than pulling it diagonally across adjacent connectors, and leave enough clearance for insertion, removal and front-panel airflow.
Position Within the Length Range
MFS1S00-H001V is the shortest of 10 verified length options in this family. It is the preferred choice when the port positions are close and cable slack must be kept to a minimum. The next option is MFS1S00-H002V at 2m (7ft), adding 1m for a less direct routing path; selecting it unnecessarily would leave more cable to dress.
High-Density Rack Integration
In a densely populated rack, connector access and airflow are part of the link design. Choose the shortest length that follows the managed path comfortably, avoid tight bundles around the connector housings and preserve room for latch operation. Where power consumption is listed, include every populated interface in the host thermal budget rather than assessing a single cable in isolation. For this assembly, the minimum bend radius is 30mm; the stated power consumption is 4.35W Per End; the jacket material is LSZH.
Power and Thermal Planning
The rated power consumption is 4.35W Per End. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Cable Construction and Routing
This assembly uses LSZH jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Quality Assurance and Packaging
Each assembly receives a visual connector inspection and functional link check before it is coiled and protected. Packaging is selected to avoid compressing the cable into a tight bundle, and optional rack-based labels help maintain an orderly installation when many identical interfaces are populated together. Standard protective packing is used by default, with project documentation arranged when requested.
Ordering Information
Provide the exact part number, length, quantity and target interface density. For multi-rack projects, list each length separately and identify any preferred carton grouping. Host model and software information can be included for a compatibility review before production or dispatch. Keep MFS1S00-H001V associated with 1m (3ft) throughout the order and receiving record.
NVIDIA/Mellanox Compatibility and Factory Testing
The assembly is evaluated for host recognition and stable link operation, with diagnostics checked where the interface provides them. This approach verifies more than electrical or optical continuity. Exact platform and firmware information remains valuable in high-density deployments because port mode and qualification policy can differ within the same connector family. Where supported by the host, receive activity and diagnostic indications are reviewed together with the established link.
Frequently Asked Questions
Is this an original NVIDIA/Mellanox cable?
No. It is an HT-manufactured compatible alternative for equipment that specifies NVIDIA/Mellanox MFS1S00-H001V.
Can different brands be connected with the same assembly?
Only where both hosts explicitly support the complete interface and compatibility arrangement. Document each end and select the appropriate brand-specific product when required.
Does this order code cover multiple lengths?
No. MFS1S00-H001V refers here to 1m (3ft). Every other verified length has a separate part number and page in the length list.
Are separate transceivers or patch leads required?
No. This is one complete direct-attach assembly. The ends are not detachable modules and should not be separated from the cable.
Shipping and Lead Time
Available stock is normally prepared for dispatch within one to three working days, while larger production requirements are scheduled with the order. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.
