LC UPC Duplex OS2 SC Footprint Fiber Adapter with Flange, 10pcs/Pack

Singapore high-density designs should assess this item together with panel access, cable routing and the complete optical loss allowance. LC UPC Duplex OS2 SC Footprint Fiber Adapter with Flange couples two LC/UPC connectors into one continuous optical channel. Inside the housing, a zirconia ceramic sleeve holds both ferrules on a common axis, keeping insertion loss low and consistent and repeatable across hundreds of mating cycles. The flanged housing screws directly to the patch panel cutout for a permanent, vibration-proof mounting.

Product Highlights

• ≤0.2dB(Typical) Low Insertion Loss
• Color Coded for Rapid Fiber Management
• One-piece Dust Cap Keeps Adapter’s Interior Clean from Dust
• Stainless Steel Clips for Tool-less Snap-in Installation
• Available in A Variety of Connector Types

Specifications

Phosphor bronze and zirconia sleeves compared

Two sleeve materials dominate the MMC adapter market. Zirconia ceramic sleeves give the tightest alignment and are the specified selection for single-mode and high-performance multimode work, where core geometry leaves no room for eccentricity. Phosphor bronze sleeves serve legacy multimode and metallic-ferrule connectors where the tolerance requirement is looser and the cost matters more. Matching the sleeve to the application keeps both performance and budget under control.

Bulk packs and the economics of sparing

Panel work consumes adapters in dozens, not singles: a frame reload takes a full pack, and the spares kit must hold more against breakage, contamination and the MMC adapter that vanishes during a hurried re-entry. The ten-piece pack format matches that reality - one pack per panel slot covers the load-out with spares, and the unit cost drops well below single-piece pricing. Bulk packs additionally guarantee that every adapter on the patch panel is the corresponding revision, the corresponding color and the corresponding sleeve quality.

Kit planning for panel installation

A disciplined panel deployment kit counts everything before the van leaves: adapters at one pack per panel plus a spare, caps for every unused port, the screws or clips the patch panel needs, and the cleaning supplies that keep end faces serviceable. Adapters are the cheapest line on that list and the one whose absence stops the job outright. The bulk pack format makes the counting simple - two packs per slot and the slot is covered, existing and spared.

Panel cutouts and footprint discipline

Adapter panels are standardized around a handful of footprints, and the SC simplex footprint is the most common: duplex LC adapters are built to drop into the corresponding cutout, which is why LC and SC positions interchange freely on modern frames. Keeping to the standard footprint matters when a panel is re-loaded years later - the replacement adapter must fit the hole that is already there.

What adapter testing actually measures

Because an adapter contributes no signal of its own, its test is a mating test: reference connectors mate through the MMC adapter, and the inserted loss is recorded. A zirconia-sleeve adapter should add no more than 0.2 dB, and the mating must repeat that figure across cycles. Durability testing runs the mating hundreds of times and re-measures - a sleeve that wears loose announces itself as creeping loss. These figures, not the housing color, are what separates an adapter that serves for years from one that becomes the mystery fault.

Selecting the right adapter for the panel

Five decisions define the MMC adapter order: this connector interface pairing must correspond to both sides of the mating, the mounting style must fit the patch panel cutout, the polish color code must correspond to the plant, the sleeve material must suit the performance grade, and the count must cover the load-out plus spares. Getting all five right at order time is what turns a bag of couplers into a dependable panel. Where the pairing crosses connector families, the hybrid range covers the common conversions.

Quality Assurance and Factory Testing

Every adapter is inspected before packing: the sleeve bore is checked for alignment and surface finish, the housing latches are cycled for positive engagement, and sample matings from each production lot are measured for insertion loss. Accessories are checked for fit against the adapters they serve. In Singapore facilities, this check should form part of the rack-access and acceptance review.

Quotation and Factory Support

Refer to this adapter by connector pairing, mounting style, polish grade and pack quantity during the request for a quotation. For configurations outside the listed options - mixed packs, panel hardware kits or project packaging - send the requirement with the enquiry and the factory will review the manufacturable specification. Singapore and regional project orders can be reviewed for interface compatibility, packing details and delivery coordination.