10/100BASE-T SFPHPE Aruba J8177D Compatible High-Speed SFP Transceiver Module
The J8177D compatible module serves equipment requiring a High-Speed SFP interface with the listed wavelength plan optics and a 100m rating. Connection is through RJ-45. Product data, application guidance and factory verification are presented together to support high-density deployments balance optical performance, port access and thermal planning.
OEM Part Number: J8177DHT Part Number: SFP-GE-T
Product Highlights
- Compatible alternative to HPE Aruba J8177D
- High-Speed connectivity at 1000Mbps
- Specified reach: 100m
- RJ-45 / Cat 5e/6/6a (UTP) interface
- Digital diagnostic monitoring: Not Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and electrical performance testing before shipment
Specifications
| HPE Aruba Compatible | J8177D |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP-GE-T |
| Form Factor | SFP |
| Max. Data Rate | 1000Mbps |
| Max. Cable Distance | 100m |
| Media | Cat 5e/6/6a (UTP) |
| Connector | RJ-45 |
| RX_LOS | NO |
| Power Consumption | ≤1.2W |
| DDM/DOM | Not Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Bit Error Ratio (BER) | 1E-12 |
| EMC (Electro Magnetic Compatibility) | Supported |
| MTBF | 217,330 Hours |
| Protocols | IEEE Std 802.3 and 802.3ab, SFP MSA Compliant |
Applications and Optical Link Design
This copper transceiver is intended for short equipment links over the twisted-pair cabling category stated in the specifications. Typical uses include switch-to-server, switch-to-switch and rack-level connections where an RJ-45 interface is preferred over fiber. Use the required cable category, observe the rated distance and confirm that the host supports the module’s speed, power consumption and electrical operating modes.
Before deployment, check the host port type, supported data rate and firmware requirements. The High-Speed interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.
The rated 100m copper channel should be assessed as a complete cabling link. Confirm cable category, shielding practice and supported host mode before installation. A link indicator alone does not prove that the expected electrical rate has been established.
Quality Assurance and Packaging
Each J8177D compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Not Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 1000Mbps, rated reach 100m.
Ordering Information
Use J8177D as the compatibility cross-reference and SFP-GE-T as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
HPE Aruba Compatibility and Factory Testing
Compatibility testing for J8177D combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original HPE Aruba transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies J8177D, not an original HPE Aruba-branded module.
Which copper cable and connector are required?
Use RJ-45 with the specified category of Cat 5e/6/6a (UTP). The rated reach is 100m, subject to cable category, installation quality and host support.
Can it be used at a different speed or over another cable category?
Only within the multi-rate and cabling capabilities stated in the specifications and supported by the host. Confirm the required cable category, distance and auto-negotiation behavior before installation.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
