MTP-12 to LC UPC Uniboot Trunk CableMTP-12 to LC UPC Uniboot Trunk Cable, Female, 48 Fibers, OM3, Type B
Pre-terminated MTP® Elite Female backbone trunk with 48 Fibers (Base-12) on OM3 50/125μm fiber. Instead of splicing dozens of connectors on site, your installers pull one cable, mount the panels and plug in.
Standard lengths are 1m (3ft), 3m (10ft), 5m (16ft), 7m (23ft), 10m (33ft), 15m (49ft), 20m (66ft), 25m (82ft), 30m (98ft) and 40m (131ft). Because we are the manufacturer, any other length between or beyond these steps can be produced on request, with your choice of jacket color, labeling and packaging.
Product Highlights
- MTP® Elite Female (Non-Pinned) to LC Duplex Uniboot, 48 Fibers (Base-12)
- OM3 50/125μm, bend insensitive fiber
- Insertion loss ≤0.20dB, return loss ≥27dB
- Type B polarity
- 8.5-9.0mm Plenum (OFNP) round cable
- Minimum bend radius 7.5mm
- Ten standard lengths from 1m (3ft) to 40m (131ft), custom lengths built to order
Specifications
| Part Number | HD-48FMTPLCOM3 |
|---|---|
| Manufacturer | HT |
| Connector A | US Conec MTP® Elite Female (Non-Pinned) |
| Connector B | LC Duplex Uniboot |
| Fiber Mode | OM3 50/125μm |
| Wavelength | 850/1300nm |
| Polish Type | UPC to UPC |
| Polarity | Type B |
| Cable Jacket | Plenum (OFNP) |
| Fiber Count | 48 Fibers (Base-12) |
| Glass Fiber | Bend Insensitive Fiber |
| Cable Structure | Double Jacket |
| Minimum Bend Radius | 7.5mm |
| Cable Outside Diameter (OD) | 8.5-9.0mm |
| Breakout Outside Diameter (OD) | 2.0mm |
| Breakout Length | 0.84m (MTP®), 0.91m (LC) |
| Long-term Tensile Load | 200N |
| Short-term Tensile Load | 660N |
| MTP Connector Count | 4 |
| LC Connector Count | 24 |
| MTP Connector IL | ≤0.20dB |
| LC Connector IL | ≤0.20dB |
| MTP Connector RL | ≥27dB |
| LC Connector RL | ≥20dB |
| Attenuation at 850nm | ≤2.3dB/km |
| Attenuation at 1300nm | ≤0.6dB/km |
| Operating Temperature | -10 to 60°C (14 to 140℉) |
| Storage Temperature | -10 to 70°C (14 to 158℉) |
Applications
Install this trunk wherever many fibers must move between two termination points at once. The 48 Fibers (Base-12) construction concentrates the equivalent of many duplex jumpers into a single assembly, which is exactly what high density spine and leaf cabling needs. The assembly is shipped on a reel or coil with pulling protection, ready for a single pull through trays and conduits.
Trunk Construction and Polarity
The trunk uses a double jacket design: a rugged outer sheath protects the whole bundle, while each breakout leg keeps its own jacket and numbering. Base-8 and Base-12 constructions are available depending on the fiber count. Polarity follows the Type shown in the table, and pulling eyes or mesh grips can be fitted for installation.
Ordering Information
Ordering is simple: send us HD-48FMTPLCOM3 and your required lengths and quantities, and we return a factory quote the same working day. The 1m (3ft) version is the standard model; Small trial orders are welcome before you commit to a full project rollout.
Built to Your Spec
As a factory we can modify almost every detail of this product: length, jacket material and color, polarity, gender, breakout geometry, labeling and packaging. Non-standard variants are routine work for us, not a special project.
How We Pack
Every cable is protected with dust caps and individual packaging before being boxed for shipment. Batch test reports and your own part number labels can be included in each bag.
Quality and Testing
Every MPO/MTP assembly leaving our factory is 100% tested for insertion loss and return loss, with end face geometry checks on the multi-fiber ferrules. Controlled polishing keeps the loss budget stable across the whole batch, which matters when several mated pairs sit in one link.
