DSFP to DSFP-100G-AOC-30M98FTDSFP to DSFP-100G-AOC-30M98FT 100G DSFP 2 x 50G PAM4 Active Optical Cable, 30m (98ft)
For densely populated equipment, the fixed 30m (98ft) version of Generic DSFP to DSFP-100G-AOC-30M98FT offers a clearly defined 100G link without separate optical modules or patch cords. The AOC assembly uses DSFP to DSFP; its power, mechanical and diagnostic details are listed where supplied so port density and cable management can be assessed together.
OEM Part Number: DSFP to DSFP-100G-AOC-30M98FTHT Part Number: DSFP to DSFP-100G-AOC-30M98FT
Product Highlights
- HT-manufactured AOC assembly in 30m (98ft)
- 100G connectivity at 100Gbps
- Interface configuration: DSFP to DSFP
- Fixed length and part number: 30m (98ft), DSFP to DSFP-100G-AOC-30M98FT
- Cable construction: Active Optical Cable
- Maximum power consumption: 3.5W
- Minimum bend radius: 30mm
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | DSFP to DSFP-100G-AOC-30M98FT |
|---|---|
| Manufacturer | HT |
| Form Factor | DSFP to DSFP |
| Max. Data Rate | 100Gbps |
| Cable Length | 30m (98ft) |
| Cable Type | Active Optical Cable |
| Wavelength | 850nm |
| Minimum Bend Radius | 30mm |
| Transmitter Type | VSCEL |
| Receiver Type | PIN |
| Max. Power Consumption | 3.5W |
| Modulation Format | 2x50G-PAM4 |
| Power supply | 3.3V |
| Bit Error Ratio (BER) | 2.4E-4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Jacket Material | OFNP |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | DSFP MSA, IEEE 802.3cd, RoHS (Lead-free) |
Signal and Lane Configuration
The listed modulation format is 2x50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
Longer assemblies require disciplined cable dressing. For DSFP to DSFP-100G-AOC-30M98FT at 30m (98ft), use the intended managers rather than a diagonal route across the rack, and leave enough space to release each connector. Any service allowance should be loose and supported, with the integrated optical cable and both optical engines protected throughout the path. The next shorter verified assembly is DSFP to DSFP-100G-AOC-20M66FT at 20m (66ft), which is the better comparison when the managed route leaves substantial unused cable.
Position Within the Length Range
DSFP to DSFP-100G-AOC-30M98FT is the longest of 9 verified length options in this family. Compared with DSFP to DSFP-100G-AOC-20M66FT at 20m (66ft), it provides 10m of additional reach for a longer vertical drop, a wider rack or an adjacent-cabinet route. Confirm that the complete path requires this length, because unused slack still needs supported, bend-safe storage.
High-Density Rack Integration
In a densely populated rack, connector access and airflow are part of the link design. Choose the shortest length that follows the managed path comfortably, avoid tight bundles around the connector housings and preserve room for latch operation. Where power consumption is listed, include every populated interface in the host thermal budget rather than assessing a single cable in isolation. For this assembly, the minimum bend radius is 30mm; the stated power consumption is 3.5W; the jacket material is OFNP.
Power and Thermal Planning
The rated power consumption is 3.5W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Cable Construction and Routing
This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Network and Protocol Considerations
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include DSFP MSA, IEEE 802.3cd, RoHS (Lead-free). Confirm that the host firmware and port configuration support the same operating mode.
Quality Assurance and Packaging
Each assembly receives a visual connector inspection and functional link check before it is coiled and protected. Packaging is selected to avoid compressing the cable into a tight bundle, and optional rack-based labels help maintain an orderly installation when many identical interfaces are populated together. Standard protective packing is used by default, with project documentation arranged when requested.
Ordering Information
Provide the exact part number, length, quantity and target interface density. For multi-rack projects, list each length separately and identify any preferred carton grouping. Host model and software information can be included for a compatibility review before production or dispatch. This page’s fixed configuration is 30m (98ft); another length must be quoted under its corresponding part number.
Generic Compatibility and Factory Testing
The assembly is evaluated for host recognition and stable link operation, with diagnostics checked where the interface provides them. This approach verifies more than electrical or optical continuity. Exact platform and firmware information remains valuable in high-density deployments because port mode and qualification policy can differ within the same connector family. The check includes receive activity and diagnostic indications, followed by a final inspection of both ends.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
How should an unused assembly be stored?
Protect both connector ends, keep the cable in a loose bend-safe coil and retain its part-number label so the length and compatibility identity remain traceable.
Can different brands be connected with the same assembly?
Only where both hosts explicitly support the complete interface and compatibility arrangement. Document each end and select the appropriate brand-specific product when required.
Does this order code cover multiple lengths?
No. DSFP to DSFP-100G-AOC-30M98FT refers here to 30m (98ft). Every other verified length has a separate part number and page in the length list.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production quantities confirmed at order stage. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.
