CWDM-SFP1G-EZXGeneric CWDM-SFP1G-EZX Compatible 1G SFP Transceiver Module
Built for hosts recognizing CWDM-SFP1G-EZX, this HT-manufactured SFP module delivers 1G transmission at 1270nm. Its rated reach is 100km, with Duplex LC as the physical interface. The specifications and engineering guidance below support high-density deployments balance optical performance, port access and thermal planning, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: CWDM-SFP1G-EZXHT Part Number: CW-SFP1G100-27
Product Highlights
- Compatible alternative to Generic CWDM-SFP1G-EZX
- 1G connectivity at 1000Mbps
- Optical wavelength: 1270nm
- Specified reach: 100km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 ~ 70°C (32 ~ 158°F)
Specifications
| HT Part Number | CW-SFP1G100-27 |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP |
| Max Data Rate | 1000Mbps |
| Wavelength | 1270nm |
| Max Cable Distance | 100km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | DFB CWDM |
| Receiver Type | APD |
| Receiver Sensitivity | < -30dBm |
| SMSR | 30dB |
| TX Power | 0~5dBm |
| RX Power | -32~-8dBm |
| Power Consumption | ≤1W |
| Power Budget | 32dB |
| EMC (Electro Magnetic Compatibility) | Supported |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 ~ 70°C (32 ~ 158°F) |
| Protocols | MSA Compliant |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 1G interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.
For this 1270nm interface, verify channel spacing and filter compatibility. Passive filters add loss even without active equipment, so assess 100km using the complete channel rather than fiber distance alone.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0~5dBm; receiver sensitivity is < -30dBm; the stated optical power budget is 32dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 1000Mbps, wavelength 1270nm, rated reach 100km.
Ordering Information
Quote HT part number CW-SFP1G100-27 together with OEM reference CWDM-SFP1G-EZX and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Generic Compatibility and Factory Testing
Compatibility testing for CWDM-SFP1G-EZX combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 100km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
