10/100BASE-T SFPEricsson CWDM-SFP10G-1270-10-I Compatible 10G SFP+ Transceiver Module
Built for hosts recognizing CWDM-SFP10G-1270-10-I, this HT-manufactured SFP+ module delivers 10G transmission at 1270nm. Its rated reach is 10km, with Duplex LC as the physical interface. The specifications and engineering guidance below support high-density deployments balance optical performance, port access and thermal planning, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: CWDM-SFP10G-1270-10-IHT Part Number: CWDM-SFP10G-1270-10-I
Product Highlights
- Compatible alternative to Ericsson CWDM-SFP10G-1270-10-I
- 10G connectivity at 10.31Gbps
- Optical wavelength: 1270nm
- Specified reach: 10km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -40 to 85°C (-40 to 185°F)
Specifications
| HT Part Number | CWDM-SFP10G-1270-10-I |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ |
| Max Data Rate | 10.31Gbps |
| Wavelength | 1270nm |
| Max Cable Distance | 10km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | DFB |
| Receiver Type | PIN |
| TX Power | -1~5dBm |
| Receiver Sensitivity | <-14.4dBm |
| Power Budget | >15dB |
| Receiver Overload | >0dB |
| Typical Power Consumption | <1.2W |
| Extinction Ratio | >3.5dB |
| DDM/DOM | Supported |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| Protocols | SFP+ MSA, SFF-8472 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
Wavelength-selective links require the exact channel plan at both ends. Confirm that filters pass 1270nm, then include their insertion loss in the 10km power budget. A nearby channel is not a substitute for the specified wavelength.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -1~5dBm; receiver sensitivity is <-14.4dBm; the stated optical power budget is >15dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 10.31Gbps, wavelength 1270nm, rated reach 10km.
Ordering Information
Quote HT part number CWDM-SFP10G-1270-10-I together with OEM reference CWDM-SFP10G-1270-10-I and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Ericsson Compatibility and Factory Testing
Factory verification starts with the expected CWDM-SFP10G-1270-10-I identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Ericsson transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies CWDM-SFP10G-1270-10-I, not an original Ericsson-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
