10/100BASE-T SFPDell PowerConnect 320-2879 Compatible 1.25G SFP Transceiver Module
The 320-2879 compatible module serves equipment requiring a 1.25G SFP interface with 1310nm optics and a 10km on SMF rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support high-density deployments balance optical performance, port access and thermal planning.
OEM Part Number: 320-2879HT Part Number: SFP1G-LX-31
Product Highlights
- Compatible alternative to Dell PowerConnect 320-2879
- 1.25G connectivity at 1.25Gbps
- Optical wavelength: 1310nm
- Specified reach: 10km on SMF
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| Dell Compatible | 320-2879 |
|---|---|
| Manufacturer | HT |
| HT Part Number | SFP1G-LX-31 |
| Form Factor | SFP |
| Max. Data Rate | 1.25Gbps |
| Wavelength | 1310nm |
| Max. Cable Distance | 10km@SMF |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | FP |
| Receiver Type | PIN |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| TX Power | -9.5~-3dBm |
| Receiver Sensitivity | < -20dBm |
| Power Consumption | ≤1W |
| Receiver Overload | -3dBm |
| Bit Error Ratio (BER) | 1E-12 |
| Extinction Ratio | >9dB |
| EMC (Electro Magnetic Compatibility) | Supported |
| MTBF (LX) | 4,761,904 Hours |
| Protocols | IEEE 802.3ah-2004, IEEE 802.3z, SFF-8472, SFP MSA (INF-8074i) Compliant |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 1.25G interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 10km on SMF route. Keep the Duplex LC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -9.5~-3dBm; receiver sensitivity is < -20dBm. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 1.25Gbps, wavelength 1310nm, rated reach 10km on SMF.
Ordering Information
When ordering, specify 320-2879, SFP1G-LX-31, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Dell PowerConnect Compatibility and Factory Testing
Factory verification starts with the expected 320-2879 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Dell PowerConnect transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 320-2879, not an original Dell PowerConnect-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 10km on SMF, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
