25GBASE-SR-EArista Networks 25GBASE-SR-E Compatible 25G SFP28 SR-E Transceiver Module
The 25GBASE-SR-E compatible module serves equipment requiring a 25G SFP28 interface with 850nm optics and a 30m rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support high-density deployments balance optical performance, port access and thermal planning.
OEM Part Number: 25GBASE-SR-EHT Part Number: 25GBASE-SR-E
Product Highlights
- Compatible alternative to Arista Networks 25GBASE-SR-E
- 25G connectivity at 25.78Gbps
- Optical wavelength: 850nm
- Specified reach: 30m
- Duplex LC / MMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Arista Network Compatible | 25GBASE-SR-E |
|---|---|
| Manufacturer | HT |
| HT Part Number | 25GBASE-SR-E |
| Form Factor | SFP28 |
| Max Data Rate | 25.78Gbps |
| Wavelength | 850nm |
| Max Cable Distance | 30m |
| Connector | Duplex LC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| TX Power | -8.4~2.4dBm |
| Receiver Sensitivity | -10.2 dBm |
| Power Budget | 1.9dB |
| Receiver Overload | 2.4 dBm |
| Power Consumption | <0.6W |
| Extinction Ratio | 2dB |
| CDR | TX and RX |
| FEC Function | Support RS-FEC |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | SFF-8472, SFF-8024, SFF-8431, SFF-8432, IEEE 802.3by, IEEE 802.3cc |
| DOM | Supported |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 25G interface configuration must match the remote equipment; sharing a SFP28 housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 30m reach. Keep the Duplex LC end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8.4~2.4dBm; receiver sensitivity is -10.2 dBm; the stated optical power budget is 1.9dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
High-Density Port and Thermal Planning
In a densely populated chassis, connector access and airflow form part of the optical-link design. Confirm that neighboring modules and patch leads leave room for latch operation, and include listed power consumption in the host thermal budget. Assess port density together with fiber management. For this model, the principal parameters are data rate 25.78Gbps, wavelength 850nm, rated reach 30m.
Ordering Information
When ordering, specify 25GBASE-SR-E, 25GBASE-SR-E, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Arista Networks Compatibility and Factory Testing
Compatibility testing for 25GBASE-SR-E combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Frequently Asked Questions
Is this an original Arista Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 25GBASE-SR-E, not an original Arista Networks-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF. The specified maximum reach is 30m, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
